Q345B Steel

power management ic with lin and high speed can

power management ic with lin and high speed can

power management ic with lin and high speed can

5V and 24V Line Drivers Power Electronics

IC-Haus introduced the iC-HD2, iC-HD7 and iC-HE line drivers for 5 V and 24 V industrial encoder/sensor applications. The output drivers are designed for cable impedances in the range of 30 to 140 Ohms. Due to the unique integrated wave impedance adaption, reflected signals coming from the non-terminated line end at the receiver will be absorbed and not back reflected again, thus AFE031 data sheet, product information and support TIThis monolithic integrated circuit provides high reliability in demanding powerline communications applications. The AFE031 transmit power amplifier operates from a single supply in the range of 7 V to 24 V. At maximum output current, a wide output swing provides a 12-V PP (I OUT = 1.5 A) capability with a nominal 15-V supply. The analog and

CAN Bus Interface Description CANbus Pin Out, and Signal

CAN Bus Pin Out. The Can Bus pinout for the 9-pin D connector is shown in the table below. Additional connector styles are listed on the CAN Bus Connector Pin out page, or CAN Bus Round Connector Pin out. Many of the additional connector pin outs are used with CANopen and include:10-pin header [5 x 2 multipole], RJ10 [Modular Connector Jack], RJ45 [Modular Connector Jack], 5-pin mini CAN bus physical layer - Pico autoFor example, an IC might act as an interface between the powertrain and convenience CAN buses to provide, amongst other things, automatic door locking functionality; e.g. a vehicle speed message from the ABS control unit on the higher speed bus can be transmitted to the convenience control unit on the lower speed bus via the IC. The convenience control module would then know to lock the doors once CAN bus physical layer - Pico autoOn some CAN buses, where the attached control units share a common reference potential (e.g. the chassis ground), the CAN controllers can switch to single line operation to provide fault tolerance in the event of an open circuit on either the CAN-L or CAN-H lines. High speed CAN buses use terminating resistors to remove transmission reflections

Controller Area Network (CAN) Implementation Guide

The ADM3053 is a fully isolated high speed CAN transceiver with 2.5 kV rms signal and power isolation. The ADM3052 is a 5 kV rms signal isolated high speed CAN transceiver with an integrated bus voltage regulator to use 24 V bus power (for example, as in DeviceNet applications). The ADM3051 is a nonisolated high speed CAN transceiver. Introduction to the Local Interconnect Network (LIN) Bus Oct 14, 2020 · The Local Interconnect Network (LIN) bus was developed to create a standard for low-cost, low-end multiplexed communication in automotive networks. Though the Controller Area Network ( CAN ) bus addresses the need for high-bandwidth, advanced error-handling networks, the hardware and software costs of CAN implementation have become prohibitive for lower performance devices such Low on resistance, High speed switching Expanded Lineup Aug 19, 2020 · Your analog power IC and the best power management. MENU. The products which released this time are general-purpose MOSFET with low on resistance and high speed switching. It can be used for various applications such as relay circuits and switching circuits. The gate protection diode is built-in as a static protection.

MAX13041 ±80V Fault-Protected High-Speed CAN Transceiver

The MAX13041 ±80V fault-protected, high-speed controller area network (CAN) transceiver is ideal for high-speed automotive network applications where high reliability and advanced power management are required. The device links a CAN protocol controll NCV7344:CAN FD Transceiver, High Speed, Low PowerThe NCV7344 is an addition to the CAN highspeed transceiver family complementing NCV734x CAN standalone transceivers and previous generations such as AMIS42665, AMIS3066x, etc. The NCV7344 guarantees additional timing parameters to ensure robust communication at data rates beyond 1 Mbps to cope with CAN flexible data rate requirements Power management IC with LIN and high speed CANPower management IC with LIN and high speed CAN Features Two 5V voltage regulators for microcontroller and peripheral supply No electrolytic capacitor required on regulator outputs Ultra low quiescent current in standby modes Programmable reset generator for power-on and undervoltage Configurable window watchdog and fail safe output

UJA1075A High speed CAN/LIN core SBC NXP

The UJA1075A supports the networking applications used to control power and sensor peripherals by using a high-speed CAN as the main network interface and the LIN interface as a local sub-bus. The UJA1075A is designed to be used in combination with a microcontroller that incorporates a CAN controller. The SBC ensures that the microcontroller always starts up in a controlled manner. UJA1075A High speed CAN/LIN core SBC NXPThe UJA1075A supports the networking applications used to control power and sensor peripherals by using a high-speed CAN as the main network interface and the LIN interface as a local sub-bus. The UJA1075A is designed to be used in combination with a microcontroller that incorporates a CAN controller. The SBC ensures that the microcontroller always starts up in a controlled manner. USB Signaling and Power Management ICs - Maxim IntegratedMaxim provides wide range of products that were designed for use in USB signaling and USB power management. Our USB battery charger ICs offer USB-C and BC1.2 adapter detection, reduce charge time and heat while maximizing safety. Our USB battery charger detector ICs enable universal and optimal charging over USB-C or legacy ports.

L99PM62GXP - Power Management IC with LIN and High

The L99PM62GXP is a power management system IC that provides electronic control units with enhanced system power supply functionality, including various standby modes, as well as LIN and HS CAN physical communication layers. The devices two low-drop voltage regulators supply the system microcontroller and external peripheral loads such as sensors and provide enhanced system standby

Contact us

Email: [email protected]